bout ihe lime my grandson was beginning to walk, I got to thinking it was also lime lo build that kiddie car I'd been remembering from 'way back in my childhood. Remember that solid-wood beauty you cruised around on when you were a two-year-old? If I close my eyes. I can still picture it. And. if I try very hard, I can faintly recall what it felt like to zoom off the dining room carpet, wheel her through the door and onto the kitchen linoleum, flat out. Wow!
But I couldn't make one like that. That one had a turned front steering assembly, together with nicely turned wooden handles; and I had no lathe.
While I tried to think my way around the no-lathe problem, I also thought of some other changes that might improve a new model over the one from my youth, if that's possible. Two ideas came to mind. First was the concept of the pickup truck, which has grabbed the imagination of automobiling in America
Glue sides and —' fasten with 7«-in. dia. dowels.
Pean axle ends with center punch or install cotter pins.
Peen shaft ends or insUK cottar pins.
Screw bites — into long grain of dowel.
today—pickups are in. The other idea? I've heard more than one mother complain about her kids leaving toys spread all over the place. Was it possible a youngster could get excited enough about having a "pickup" that, at the end of the day, the kid would really enjoy driving around, picking up all those stray toys? Why not try it?
To help visualize the toy, I made a sketch. (See page 33.) I usually do that. It helps me clear up the design and often leads to a better way of doing something. For instance, I've got this thing about making do with what I've got. I've carried this philosophy around with
Screw pickup bed to seat, no glue.
Leave dowel ends proud me for a long time. "You have no lathe, so what can you do about that steering column?," I asked myself. I like the challenge; nice discipline, and it keeps your thinking flexible, too.
When I checked my shop for materials on hand. I found I had the wood (I used red oak) but wondered what I might use for the axles and yoke pin. My old can of large bolts turned up none the right size for those jobs. That's when my sketch led to the idea of another way of doing it. I had a piece of Vi6-in. steel rod left over from another job. And a can of assorted flat washers produced six which fit snugly on the Vi<.-in. rod. I knew that I could peen the ends with a hammer to hold the wheels on, but I came up with the idea of doing it with a center punch near the edge of the rod, instead, as shown in the detail on the drawing. (See Fig. 1.) I tried it on a sample and, by gosh, it worked! Sec what I mean? Make do.
One night while I was supporting my wobbling grandson as he tried those early first steps, I had my daughter measure him from crotch to floor. That's how I came up with a 9-in. seat height for the pickup.
After the sketch, I usually get right on with the construction, eyeing the thing as I go along. I get the "feel" of the dimensions as I work—you know, "that looks about right there." Don't get me wrong. I like to be accurate. But, especially while designing (let's say this pickup is a sort of prototype), I prefer to work to the feel of things. I find that more satisfying.
A little while after I had built the pickup and given it to my grandson, his mother said she thought it could be built wider between the rear wheels—it was a bit tipsy. It also occurred to me that the pickup would roll more easily over thick carpets if the wheels were 6-in. dia. instead of 5-in., like mine. I asked AMERICAN WOODWORKER to take all this into consideration on the detail drawings. (Editor's Note: We did.) You know, there's always room for improvement—or at least, adaptation.
By the way, the "pick-it-up" idea didn't help a bit. His mother says he's still a mess—lovingly ... but he sure loved that pickup. A
Jack Fisher is a woodworker and painter in New Hope, PA. Before he retired in 1978, he taught Industrial Arts at New Hope/Solehury High School.
The steering assembly pivots on a Vu-ki. dia steel rod through the seat.
•^finishing materials'arc the-
• aval fable to achl£V»the lodjk, durability, or reversibility (ability of the finish to ^ be stripped off or repaired) I want on various projects. 7 to better understand the different finishes, I find
1 • ^^fei}^ durable r\nish, suit: ■tr L 1 aif«Tfor the finest furniture :3rw.~?na^#cii\oId. UjtpjNo ap-oy brasniu^. sprt^hg or padding, and It's an easy ¿h UfTep^.^tyellac is apgrftpwfote for atiy surface snbjecit'd to witter br.sp3tetfalcoholic drinks' ^¿Iknfc-is a resin'^erated trr insects whj<;h attach n> selves to ccrtarxi^roes in and around northern iysin is-scrd'pea frorri tb? twigs and branches fie Trees. Then it's cleaned, melted, and formed into ge tHiTWsheets thai are broken up. into flakes and fbe world*- Y .. (<3il can bjj^sftelJ^fl^kes byjhcipound and make fttoh ^vdf^pOTnfe ihMtr^sin alcohol, or i can Jun; j^cnmird ¿lielhic in a cantiWmosi paint r^jM^^fifeMert fogkrtheir.own shpltec just to
Was this article helpful?
There are a lot of things that either needs to be repaired, or put together when youre a homeowner. If youre a new homeowner, and have just gotten out of apartment style living, you might want to take this list with you to the hardware store. From remolding jobs to putting together furniture you can use these 5 power tools to get your stuff together. Dont forget too that youll need a few extra tools for other jobs around the house.