Mitered Bridle Joint

A table saw and a simple, shop-made jig are all you need to make strong, tight-fitting miter joints.


The key to a strong mitered bridle joint is getting a snug fit on the mating parts. For this reason, I like to cut the slot first and then sneak up on the thickness of the tenon. To cut the slots, you'll need a way to support the workpiece on end. You can use either a shop-made or commercial tenoning jig on the table saw (Figure 1). I use a dado blade for ]A" or larger slots. Slots for Vs"-thick tenons can be cut with a single blade.

DETERMINING SIZE. The thickness of the slot is governed by the thickness of the workpiece. A good guide is to make it one third the thickness of the workpiece. (For iCt example, a '4" slot for 34" stock.)

SLOT. To position the workpiece correctly, I set the rip fence so that the distance between the blade

Miter joints look great on a project. But a weakness of miter joints is that they rely on end grain for gluing strength. And end grain joints are pretty weak. There are several ways to strengthen a miter joint. But a traditional method that I like to use is a mitered bridle joint.

A mitered bridle joint is similar to an open mortise and tenon joint. One piece has a through slot and the other a matching tenon. But the shoulders of both pieces are mitered. The benefit of this joint is that it offers plenty of glue surface for a strong joint (main photo).

A simple jig makes cutting slots easy

Set blade height same as width of yy workpiece and the jig is one third the thickness of the workpiece. Then you can clamp the workpiece in the tenoning jig and make the first cut. Simply flip the workpiece for the second cut. This will center the slot on the thickness of the workpiece.

MITER. To mark the mitered ends, you can use a combination square. Then set your miter gauge at 45° and make the cut (Figure 2).

TENONS. Once you have the slots cut, making the tenons on the mating pieces to fit is pretty simple. I've found that the easiest way to cut these is with a dado blade and a miter gauge, laying the workpiece flat on the saw table.

Using the slotted workpiece as a gauge, set the height of the dado blade so it's just below the slot opening. I like to test the blade setting on a scrap piece. This way I can sneak up on the thickness of

Set the blade height using a test piece the same thickness as the workpiece

Raise blade and make cuts until test tenon fits slot

Fine-tune tenon thickness with a sanding block

Position workpiece against fence

Trestle Slot Drafting Table

Position workpiece against fence

Fine-tune tenon thickness with a sanding block the tenon by raising the blade a bit until it fits in the slot (Figure 3).

Once you have the blade height set, adjust the miter gauge to 45°, mark a layout line and align it with the saw blade. You can set the rip fence as a stop for the first cut. Then remove the waste with multiple passes, working toward the end until the tenon is shaped on one of the faces (Figure 4). Then flip the workpiece, adjust the miter gauge, and make the same cuts on the opposite face (Figure 5).


Using a dado blade to cut the tenons can leave saw marks. You'll want to smooth the cheeks so the tenons will fit without gaps.

SMOOTHING. A sanding block is a good tool to smooth the cheeks

(Figure 6). If the tenon is a little too thick, a shoulder plane or chisel will remove more material. But be careful. It's best to remove small amounts of material from both faces and keep checking until you have a perfect fit that's centered. Once the tenon fits in the slot, you can add the glue.

CLAMPING. Although you can use bar or pipe clamps, I prefer to use a band clamp for assembling mitered joints. This way, all the corners will be pulled together at once for a good fit. Add clamping blocks and additional clamps to apply pressure to each joint (photo at right).

Adding a tenon always makes a stronger joint. But the tenon doesn't have to be in the center, as you can see in the box below. EiS

Clamping blocks and a clamp at each joint ensures a tight miter.

Clamping blocks and a clamp at each joint ensures a tight miter.

Double Bridle JointMitre Bridle JointMiter Tight Picture Frame Clamp

Each piece is identical and has both a tenon and slot on each end.

Worth A Look; Double Bridle Miter Joint

A variation of the joint shown above is the double bridle miter joint. The first thing you'll notice about this joint is that each piece has a slot and a tenon. This makes the joint a good alternative if you want a similar look along both edges.

DIFFERENCES. One of the interesting features of this joint is that both halves are identical. When you flip one side of the frame, the offset tenon meets the slot, and the joint goes together (first photo at right). This makes laying out and cutting the joint a little easier.

This type of joint is most commonly used on frames for artist's canvases, but can be used on other types of frames as well.

Each piece is identical and has both a tenon and slot on each end.

Bridle Joint

The Veritas sharpening jig holds the tool securely. It slides back and forth in the machined groove to provide a consistent, square edge.

Bridle Joint


Grindi jig

Was this article helpful?

0 0
Woodworking Tools and Installation Tips

Woodworking Tools and Installation Tips

There are a lot of things that either needs to be repaired, or put together when youre a homeowner. If youre a new homeowner, and have just gotten out of apartment style living, you might want to take this list with you to the hardware store. From remolding jobs to putting together furniture you can use these 5 power tools to get your stuff together. Dont forget too that youll need a few extra tools for other jobs around the house.

Get My Free Ebook


  • Adele
    How to cut a mitered bridle joint?
    9 years ago
  • madihah
    How to make a mitered bridle joint?
    8 years ago
  • millie
    How to cut mitered double bridle?
    7 years ago
  • millar
    How I make a corner Bridle Joint?
    7 years ago
  • william
    How to make a mitered corner bridle joint step by step?
    5 years ago
  • Atte
    How to make mitre faces briddle joint?
    4 years ago
  • terry
    What is mitre faced bridle joint?
    4 years ago
  • Mari Nyk
    How to make single mitred bridle joint?
    4 years ago
  • emmi
    How to make mitre corner bridle joint?
    3 years ago
  • nicla greece
    When to use milter bridle joints?
    12 months ago

Post a comment