Cutting Diagram

Tedswoodworking Plans

Ted's Woodworking Plans

Get Instant Access

CASE

A Corner Posts (4)*

13/4 X 13/4-71

B Side Rails (4)

1 x 51*-17V*

C Side Panels (4)

Va -171/2 x 591/2 plywood

D Front Rails (2)

3/4 x 43/4 - 391/2

E Lwr. Front Rail Cap (1) 1x1%- 38l*

F Upr./Lwr. Back Rails (2) 3/4 x 5Vi> - 39V*

G Middle Back Rail (1)

3/4 x 3 - 39V*

TOP & SHELF

H Top Cleats (2)

3/4 x 11/2 - 391/2

1 Top (1)

1 x22-46

J Filler Strips (2)

3/4X3-161/2

K Shelf Cleats (2)

3/4x1- 18V* hard maple

L Shelf (1)

1 x 195/8 -38 V*

DRAWER

M Front/Back (2)

3/4x7- 38 hard maple

N Sides (2)

3/4 x 7 -171/4 hard maple

O Bottom (1)

1/4 -171/4 x 371/4 plywood

P Guide Runners (2)

3/4 x 1/4 -16V2 hard maple

Q Guided)

3/4x2-18Vs hard maple

R Drawer Runners (2)

3/4x11/2'- 17Vi hard maple

S False Front (1)

3/4 X 77/8 - 383/g

DOORS & CASE BACK

T Door Stiles (4)

1 x 21/? - 547/8

U Door Rails (4)

1 x 43/4 - 1415/16

V Door Panels (4)

1/4- 1415/16 x 473/4 ply.

W Closet Pole(1)

1 Va dia. - 393/8 fir dowel

X Pole Brackets (2)

3/4X2-3

Y Upper Back (1)

i/4 - 39V* x 493/8 plywood

Z Lower Back (1)

1/4 - 391* x 81/8 plywood

*Note: All parts cherry except where noted

1" x 6" -96" Cherry (2 boards @ 5 Bd. Ft. ea.)

13A" x 8" - 84" Cherry (9.33 Bd.Ft.)

3A" x 8V2" - 84" Cherry (5 Bd. Ft.)

s

J 1 J t^l

1

%" x 5" - 84" Cherry (2.9 Bd. Ft.)

D

D

m

x 6" - 84" Cherry (3.5 Bd. Ft.)

F

F

%

3A" x 3V2" - 84" Cherry (2.0 Bd. Ft.)

G 1 G t&m.

3A" x T/z" - 84" Maple (4.4 Bd. Ft.)

M

- gP

ALSO NEED: Four 4' x 8' sheets of 1A" cherry plywood

1" x 6" -96" Cherry (2 boards @ 5 Bd. Ft. ea.)

L

L

1 ■

V x 6" -96" Cherry (2 boards

5 Bd. Ft. ea.)

1

1

1 " x 5V2" - 96" Cherry ( 2 boards

@ 4.6 Bd.Ft.)

U

U Kl

13A" x 8" - 84" Cherry (9.33 Bd.Ft.)

ALSO NEED: Four 4' x 8' sheets of 1A" cherry plywood

Optional

Inner Case

With the wardrobe completed, I turned my attention to the inner case. This small four-drawer compartment is completely optional. Ifs built almost entirely from 3A"-thick glued-up panels and will simply slide into the wardrobe.

The height of this case is determined by the drawers, which in turn are determined by the machined dovetails. (Mine were 5W tall.) If another method of joining the drawers is used, you can make the drawers as short or tall as you want.

I began by gluing up panels for the top and bottom (A), sides (B), and center divider (C), see Fig. 1. Then I cut all the panels to size except the center divider. It will be cut to fit inside the case later.

Wood Drawer Diagrams

TOP/BOTTOM

MATERIALS

C Center Divider (1)

E Drawer Fronts (4)

F Drawer Backs (4)

G Drawer Sides (8)

I Drawer Runners (8)

J Side Filler Strips (2) K

Va - 37V8 x 11Vi6 plywood 3/4X5V4- 1715/16 3/4 x 51/4 - 1715/ie hard maple 3/4 x 51/4 -163/4 hard maple 1/4 - 163/4 x 173/16 plywood 3/4 x 7/i6 -17 hard maple 3/4X3- 16Vz 1/2 X3 - 383/g

Back Filler Strip (1) *Note: All parts cherry except where noted Also Needed: One 12" x 48" piece of 1/4" plywood

Was this article helpful?

0 0
A Course In Wood Turning

A Course In Wood Turning

Ever wondered what wood turning is all about? Here are some invaluable information on how to make beautiful items out of wood! That one little strategy from A Course In Wood Turning that I implemented not only worked, but the results were completely astonishing. I had never seen anything like it! Now, keep in mind that I had tried a lot of other products up until this point. You name it, I probably tried it! That’s how desperate I was to improve my skills with wood turning.

Get My Free Ebook


Post a comment